• 4" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
  • Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
  • 4.5" SDWH stainless steel timber hex screws by Simpson Strong-Tie
  • 5" Simpson SDWH Stainless steel Timber Hex Screw
  • 6" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
  • 8" SDWH stainless steel timber hex screws by Simpson Strong-Tie
  • 3" SDWH stainless steel timber hex screws by Simpson Strong-Tie
  • 10" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
  • 12" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 4" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 4.5" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 5" Simpson SDWH Stainless steel Timber Hex Screw
    • 6" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 8" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 3" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 10" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 12" SDWH stainless steel timber hex screws by Simpson Strong-Tie

    SDWH Timber-Hex SS Screw

    Vendor: Simpson Strong-Tie
    SKU: SDWH19400SS-R20
    $54.00
    Shipping is FREE!
    Drive Type: 5/16" Hex
    Length: 4"
    Box QTY: 20
    View Full Details
    • 4" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 4.5" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 5" Simpson SDWH Stainless steel Timber Hex Screw
    • 6" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 8" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 3" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    • 10" Simpson Strong-Drive SDWH Stainless steel Timber Hex Screw
    • 12" SDWH stainless steel timber hex screws by Simpson Strong-Tie
    1 / 1
    Press & drag to view
    Product DetailsRelated ProductsTechnical SpecsReviews

    The Strong-Drive® SDWH Timber-Hex SS heavy-duty structural screw is made from Type 316 stainless steel for the highest corrosion resistance in marine and coastal work. A thick shank, sharp point and hex-washer head give reliable strength with fast installation.

    Designed for docks, piers, wharves, boardwalks and ledgers, this stainless steel hex screw holds long term in wet, salt-exposed conditions where coated and galvanised fasteners eventually fail.

    Key Features

    • Type 316 stainless steel for maximum corrosion protection
    • No predrilling necessary in most applications
    • Driver bit included (replacement driver bit - BITHEXR516-R1 or BITHEXR12-R1)
    • Can be used in ledger applications
    • Unique “box” thread design with raised-ridge technology significantly reduces driving torque
    • Hex-washer head provides a large bearing area
    Specifications

    Coating/Material: 316 Grade Stainless Steel
    Drive Type:     ⁵⁄₁₆" or ½" Hex Drive
    Head Type:     Hex Washer Head
    Thread Type:     Box Threads
    Point Type:     Sharp Point
    Product Includes

    • Timber Hex 316 stainless steel screws (quantity varies by SKU).
    • BITHEXR516-R1 or BITHEXR12-R1 driver bit.
    Applications
    • Structural wood-to-wood or engineered-wood connections
    • Construction of piers, boardwalks, wharves and ledgers.

    Related Products

    You may also like

    TECHNICAL SPECS

    SDWH SS — Allowable Shear Loads — Douglas Fir–Larch, Southern Pine, Spruce-Pine-Fir, Hem-Fir

    Table of fastener specifications with columns for fastener length, model number, thread length, and allowable shear loads.

    1. All applications are based on full penetration into the main member. Full penetration is the screw length minus the side member thickness.

    2. Allowable loads are shown at the load duration factor of CD = 1.0. Loads may be increased for load duration per the building code up to a CD = 1.6. Tabulated values must be multiplied by all applicable adjustment factors per the NDS.

    3. Table values based on testing in SPF lumber.

    4. Design values include NDS wet service factor; no adjustment required for in-service moisture content greater than 19%.

    5. Allowable loads are perpendicular or parallel to grain.

    6. Installs best with 18v high-torque cordless or 1/2" low speed drill. If splitting occurs predrill with 5/32" drill bit for SDWH19 screws and 7/32" drill bit for 0.276" screws.

    7. Allowable withdrawal load for the SDWH19 screw for DFL/SP is 155 lb./in. and for SPF/HF is 108 lb./in. Allowable load is based on inches of thread penetration into the main member.

    8. Allowable withdrawal load for the SDWH27 screw for DFL/SP is 260 lb./in. and for SPF/HF is 160 lb./in. Allowable load is based on inches of thread penetration into the main member.

    9. For LRFD values, the reference connection design values shall be adjusted in accordance with NDS-18, section 11.3.

    SDWH Timber-Hex SS Screw Spacing Requirements

    Table with fastening distance and direction guidelines for construction or manufacturing.

    1. For SDWH19 screws subject to axial loading only, use the following minimum dimensions: end distance: = 2 3/8", edge distance = 1", spacing parallel to grain = 1 5/8", spacing perpendicular to grain = 1".

    2. For SDWH27 screws subject to axial loading only, use the following minimum dimensions: end distance = 3 1/4", edge distance = 1 3/8", spacing parallel to grain = 2 3/8", spacing perpendicular to grain = 1 5/8".

    Diagram showing screw spacing requirements for timber with grain direction indicated

    Featured Collections

    Discover our top picks.

    SDWH Timber-Hex SS Screw — 2024, 2021 and 2018 IRC Compliant Spacing for a Sawn Lumber Deck Ledger-to-Rim Board

    Chart detailing fastener length, nominal ledger thickness, and other specifications for a deck system.

    1. See footnotes below.

    Technical diagram of a ledger board assembly for exterior wall construction.

    SDWH Timber-Hex SS Screw — 2024, 2021 and 2018 IRC Compliant Spacing for a Sawn Lumber Deck Ledger-to-Rim Board

    Table showing deck fastener specifications for different loading conditions and nominal ledger thicknesses.

    1. Screw spacing values are equivalent to 2024/2021/2018 IRC Table R507.9.1.3(1) and 2015 IRC Table R507.2. The table above also provides screw spacing for a wider range of materials commonly used for band joists, and an alternate loading condition as required by some jurisdictions.

    2. Sawn rim board shall be spruce-pine-fir, hem-fir, Douglas fir–larch, or southern pine species. Ledger shall be hem-fir, Douglas fir–larch, or southern pine species.

    3. Fastener spacings are based on the lesser of single fastener ICC-ES AC233 testing with a safety factor of 5.0 or ledger assembly testing with a factor of safety of 5.0. Spacing includes NDS wet service factor adjustment.

    4. Multiple ledger plies shall be fastened together per code independent of the screws.

    5. Screws shall be placed 1.5" to 2" from the top and bottom of the ledger or rim board with 3" minimum and 6" maximum vertical distance between fasteners with horizontal on-center spacing per the table. End screws shall be located 6" from the end and at 1.5" to 2" from the bottom of the ledger. For screws located at least 2" but less than 6" from the end, use 50% of the load per screw and 50% of the table spacing between the end screw and the adjacent screw, and for screws located between 2" and 4" from the end, predrill using a 5/32" drill bit for SDWH19SS and 7/32" drill bit for SDWH27SS.

    6. Structural sheathing between the ledger and band shall be a maximum of 1/2" thick and fastened per code.

    7. See Ledger-to-Rim Board Assembly image above.

    Recently viewed

    Last seen items