Best Screws for Deck Framing (Joists, Ledgers, Beams)

Best Screws for Deck Framing (Joists, Ledgers, Beams)

Updated October 2026: ESR-2236 reissue (January 2026), Simpson's 2023 ledger tables, new buyer reviews and prices as of October 20.

The best screws for deck framing are code-listed structural and connector screws: Simpson Strong-Drive, picked by connection. Deck framing screws have to be listed for the connection they go in, and ordinary deck screws should not be substituted for structural fasteners in joist hangers, ledgers or other connections unless specifically permitted by the applicable instructions or building requirements. This guide covers hangers, ledgers, beams, posts, rims and blocking.

We've been building decks for over 28 years, for homes and for businesses. Every deck framing screw below has a code report number your inspector can look up.

Key Takeaways (TL;DR)

  • Joist hangers: Simpson SD Connector screws, #9 x 1-1/2" in the face and #9 x 2-1/2" in the angled holes.
  • Ledgers: Simpson SDWS Timber screws replace 1/2" lags with no pilot hole in most wood, at Simpson's own table spacing.
  • Ledger spacing: on 12 ft joists, the 2021 IRC puts 1/2" lags every 15" and 1/2" through-bolts every 29". (Note that if you are in a snow area, these specifications may be different.)
  • Beam plies: SDWS Timber at Simpson's multi-ply schedule, or two rows of 10d nails at 16" on center.
  • Post caps and post bases: Simpson SDS Heavy-Duty Connector screws, 1/4", wherever the connector lists SDS.
  • Deck screws aren't deck framing screws: about 150 Simpson connectors accept SD screws, and none accept wood or drywall screws.
  • Match the finish: galvanized hangers take galvanized fasteners, and stainless steel takes stainless steel.
  • Coastal: Simpson doesn't recommend 304 or 305 fasteners with its Type 316 connectors.
  • Price per connection: a stainless steel LUS28 takes $6.80 in SD SS screws (at the time of writing), and a ledger on 12 ft joists runs $3.97 a foot in 4" SDWH27 SS.
  • Rim to joist: end-grain screws hold about 75% of their side-grain withdrawal, so rim screws only stop joists rolling.
Connection Our pick and size Code report Pre-drill Price per connection (at the time of writing) Runner-up Carried
Joist hanger, face holes Simpson SD Connector SS, SD9112SS #9 x 1-1/2" (stainless steel hangers) ICC-ES ESR-3046 n/a, driven through the hanger holes LUS28: $3.72 (6 screws). LUS210: $4.96 (8 screws), or $2.72 at the 3000 box Galvanized SD9112 or 10d common HDG nails (ZMAX hangers) Yes, Type 316. Galvanized SD on request
Joist hanger, angled joist holes Simpson SD Connector SS, SD9212SS #9 x 2-1/2" ICC-ES ESR-3046 n/a, driven through the hanger holes $3.08 per LUS28 or LUS210 (4 screws at $0.77) 10d common HDG nails (0.148" x 3"), driven at the angle Yes, Type 316
Ledger to house rim, inland Simpson SDWS Exterior Timber, double-barrier, 0.220" IAPMO UES ER-192 No, except near the ledger ends 4": $1.08 a screw (50 box), $0.688 (250 box). Spacing from Simpson's table FastenMaster LedgerLok Yes
Ledger to house rim, coastal SDWS Timber SS, or Simpson SDWH Timber-Hex SS 0.275" x 4" or 5" ER-192 (SDWS Timber SS); Simpson IRC ledger table (SDWH SS) No, except near the ledger ends SDWH27 4": $2.98 a screw, $3.97 a foot on 12 ft joists SPAX PowerLag HCR-X Yes
Beam plies, 2-ply and 3-ply SDWS Exterior Timber inland, SDWS Timber SS coastal IAPMO UES ER-192 No, in most wood Count from Simpson's multi-ply schedule GRK RSS Yes
Beam to post Post cap with its listed fasteners, or 1/2" through-bolts in a notched post Connector listing or IRC Bored hole for bolts From the cap's load table FastenMaster ThruLok SDWH screws yes. Caps and bolts no
Post base and post cap Simpson SDS Heavy-Duty Connector, 1/4", or SDS Heavy-Duty SS ICC-ES ESR-2236 No 1-1/2" x 25 box from $30.00 ($48.00 SS). Count from the connector's table The nails the connector lists Yes
Joist to beam, on top SD9112SS in a stainless steel hurricane tie ICC-ES ESR-3046 n/a, driven through the tie holes Count from the tie's table Galvanized SD9112 in a ZMAX tie, or toe-nails Yes, Type 316
Rim joist corners SDWS Exterior Timber inland, SDWH Timber-Hex SS coastal ER-192 (double-barrier) No, in most wood SDWH27 4": $2.98 a screw FastenMaster HeadLok Yes
Mid-span blocking and nailers Eagle Claw #10 x 3" 304 stainless steel deck screws (316 near salt) None, not a structural listing Near board ends 100 box $36.00 ($45.00 for 316) 10d nails per the IRC fastening schedule Yes

Framing a whole deck? Get contractor pricing.

Framing decks for a living? Set up a contractor account first. Sign up for contractor pricing before you order.

The Best Screws for Joist Hangers are Simpson Strong-Drive SD Connector Screws

The best screws for joist hangers are Simpson Strong-Drive SD Connector screws: SD9112 (#9 x 1-1/2") in the face holes and SD9212 (#9 x 2-1/2") in the angled joist holes. Simpson's installer guide says wood and drywall screws may not replace nails in connectors.

"The inspector made me pull them" is the story we hear most about deck screws in hangers. A deck inspector calls them "not much better than drywall screws" in shear, and builders report screws that snapped the head off.

Simpson Strong-Drive SD Connector Screws (SD9112 and SD9212)

Ideal for:

  • LUS, LU, LUC and HUS hangers and hurricane ties, even where a nailer won't fit.

Why It's On The List (Key Features):

  • ICC-ES ESR-3046; a #9 SD replaces a 10d nail.
  • An LUS26 takes 4 SD9112 in the face, 4 SD9212 through the joist.

When To Use SD Connector Screws:

  • If the hanger is ZMAX, use galvanized SD. If it's Type 316, use the SD SS we carry.
  • If you want SDS screws for joist hangers, check the table: standard LUS hangers list SD.

Things to Keep in Mind

Do not mix nails and screws in the same connector unless the manufacturer's specifications explicitly allow it, and every hole filled that the table calls for. Match the metal too: stainless steel screws go in stainless steel hangers only.

Best Screws for Stainless Steel Hangers

Simpson Strong-Drive SD Connector SS Screw

$62.00 (#9 x 1-1/2", 100 box; $0.34 a screw in the 3000 box, at the time of writing)

The SD in Type 316, for stainless steel hangers and ties. ZMAX hangers take the galvanized SD, which we can order in.

Shop Product →

Specifications:

  • Material: Type 316 stainless steel
  • Drive: 1/4" hex, 0.370" washer; SD9112SS and SD9212SS
  • Best For: Simpson stainless steel hangers and ties

Highlights:

  • ✓ Listed in ICC-ES ESR-3046
  • ✓ Drives where a hammer won't swing
  • ✗ Stainless steel connectors only
  • ✗ Pricier than ordinary screws

Why SD Connector Screws Hold Up According to Buyer Reviews

These are on the galvanized SD, the same screw:

"Much better than using nails"

"They are made for all the metal deck connections. Much better than using nails."

Buyer, September 16, 2026

"I specify Simpson"

"I specify Simpson in my plans and scope of work."

Deck builder

The critical one, from September 3, 2026: inspectors call for them, but they're expensive with few competing options.

Also used: hot-dip galvanized hanger nails, 10d common (0.148" x 3"), in ZMAX hangers.

The Best Screws for Deck Ledgers are Simpson Strong-Drive SDWS Timber Screws

The best screws for deck ledgers are Simpson Strong-Drive SDWS Timber screws: double-barrier SDWS Exterior inland, Type 316 SDWS Timber SS or SDWH Timber-Hex SS near salt. These deck ledger screws go in at Simpson's table spacing, from single-screw (AC233) and full-ledger (AC13) testing.

What Screws to Use for a Deck Ledger Board?

The screws to use for a deck ledger board are 1/2" lags, 1/2" through-bolts, or a listed structural ledger screw like Simpson SDWS Timber or FastenMaster LedgerLok. The American Wood Council's DCA 6 deck guide, based on the 2015 IRC, names only lags and bolts, with washers.

Nails never count as ledger board fasteners; a 2021 IRC guide bars "nails subject to withdrawal." Half-inch lag screws and lag bolts for a ledger board follow four rules:

  • A 1/2" hole in the ledger, a 5/16" pilot in the band, a washer on every lag.
  • The lag tip passes the band's inside face. Turn it in, never hammer it.
  • Through-bolts, the other deck ledger bolts allowed, get washers at both ends.
  • Keep fasteners 2" from the top and ends, zigzagged in two rows no more than 5" apart.

Ledger board lag screw spacing and deck ledger bolt spacing, 2021 IRC, inches on center

Joist span 1/2" lag, up to 1/2" sheathing 1/2" bolt, up to 1/2" sheathing 1/2" bolt, up to 1" sheathing
6 ft and less 30 36 36
Up to 8 ft 23 36 36
Up to 10 ft 18 34 29
Up to 12 ft 15 29 24
Up to 14 ft 13 24 21
Up to 16 ft 11 21 18
Up to 18 ft 10 19 16
Structural screw spacing, ledger board Screw maker's table n/a n/a

That's the table in a 2021 IRC deck guide, numbered R507.9.1.3(1) in the 2018 and 2021 IRC. On the 2024 code, ask your town for its table. A deck ledger can't be attached to studs under it, because it assumes a solid band joist.

Deck ledger screws pattern and spacing: two staggered rows, 2 inches from the top and ends, rows no more than 5 inches apart, spacing on 12 ft joists

Can I Use Structural Screws for Ledger Board?

You can use structural screws for a ledger board when the screw has an evaluation report and you follow that maker's spacing table. An engineer puts it simply: they're "permitted only where they have been evaluated by the ICC-ES."

Things to Keep in Mind

Print the ledger table for your Simpson ledger screws and keep it on site. It's in Simpson's Fastening Systems Technical Guide.

Simpson Strong-Drive SDWS Timber Screws (SDWS Exterior and SDWS Timber SS)

Ideal for:

  • Screws to attach the ledger board to a 2x band or LVL rim: SDWS Exterior inland, SDWS Timber SS on the coast.

Why It's On The List (Key Features):

  • IAPMO UES ER-192 and Florida FL13975 for both versions.
  • No pilot hole except 2" to 4" from the ledger ends: 5/32" for SDWS Exterior, 3/16" for SDWS Timber SS.

When To Use SDWS Timber Screws:

  • If the deck is inland on ACQ or copper azole lumber, use SDWS Exterior.
  • If your plans call for SDWS Timber 4", don't swap brands without the engineer.

BEST LEDGER SCREWS FOR INLAND DECKS

Simpson Strong-Drive SDWS Exterior Timber Screw

From $33.00 (3" x 12 box, at the time of writing)

Our ledger screw for inland decks over treated lumber: double-barrier coated, T40 drive, ER-192. Salt air? Use the SDWS Timber SS.

Shop Product →

Specifications:

  • Material: Carbon steel, double-barrier coating
  • Drive: T40 6-lobe, 0.220" diameter
  • Best For: Inland ledgers, beam plies, rim corners

Highlights:

  • ✓ ER-192 and Simpson's ledger table
  • ✓ No pilot hole in most wood
  • ✗ Not for salt exposure
  • ✗ Simpson's spacing only

Why SDWS Timber Holds Up According to Builders

No reviews on our SDWS listings yet. Framers who drive them report:

"He was wrong and I proved it"

A contractor of almost 40 years: "I have had an inspector try to fail an attachment because I used these. He was wrong and I proved it."

"Give me Simpson Timber Screws any day"

That's a deck builder who pulled some recently installed LedgerLoks and found them rusted.

Also used: FastenMaster LedgerLok screws, the ledger screw builders mention most; a Georgia builder says they "pass every time every county."

The Best Screws for Deck Beams (2-Ply and 3-Ply) are Simpson SDWS Timber Screws

The best screws for deck beams built from 2-ply and 3-ply lumber are Simpson SDWS Timber screws, at the count and length in Simpson's multi-ply schedule. The code baseline is two rows of 10d nails at 16" on center along each edge, per a township guide citing 2018 IRC R507.5.

No schedule in hand? Nail it rather than guess a pattern for deck beam screws. We rank the brands in our structural timber screw roundup.

Simpson Strong-Drive SDWS Timber SS for Beams

Ideal for:

  • 2-ply and 3-ply beams near salt, on docks and boardwalks.

Why It's On The List (Key Features):

  • Type 316, Simpson's severe-exposure grade, 3" to 12".

When To Use the SDWS Timber SS on a Beam:

  • If the deck is near salt water or over a dock.
  • If the beam is inland and dry, use SDWS Exterior.

BEST BEAM SCREWS FOR WET AND COASTAL FRAMES

Simpson Strong-Drive SDWS Timber SS Heavy-Duty Screw

From $61.00 (3" x 10 box, at the time of writing)

Our pick where a beam sits over salt water or never dries out, in lengths up to 12".

Shop Product →

Specifications:

  • Material: Type 316 stainless steel
  • Drive: T50 6-lobe, 0.275" shank
  • Best For: Coastal beam plies, ledgers, docks

Highlights:

  • ✓ Lengths to 12"
  • ✓ No pilot hole in most wood
  • ✗ Needs a T50 bit and impact driver
  • ✗ Count from Simpson's schedule

Also used: GRK RSS structural screws (ESR-2442 covers multi-ply), and FastenMaster TimberLok screws.

The Best Screws for Post Caps and Post Bases are Simpson SDS Heavy-Duty Connector Screws

The best screws for post caps and post bases are Simpson Strong-Drive SDS Heavy-Duty Connector screws, 1/4" diameter, wherever the connector's table lists SDS. Simpson Strong-Tie post base screws are whatever the base lists.

SD vs SDS screws: Simpson SD Connector screws go in joist hangers and hurricane ties, SDS Heavy-Duty screws go in post bases, post caps and ties that list SDS

Ideal for:

  • Post bases, post caps and DTT2Z tension ties that list SDS.

Why It's On The List (Key Features):

When To Use SDS Screws:

  • If the table lists SD instead, use SD. Simpson's ABU44Z base lists 12 SD10112 screws.

BEST POST BASE SCREWS

Simpson Strong-Drive SDS Heavy-Duty Connector Screw

Home Depot: 4.8 ★★★★★ (408 reviews)

From $30.00 (1-1/2" x 25 box, at the time of writing)

What we drive into post bases, caps and ties that list SDS. Stainless steel connector? The SDS Heavy-Duty SS starts at $48.00.

Shop Product →

Specifications:

  • Material: Carbon steel, double-barrier coating
  • Drive: 3/8" hex, 1/4" diameter
  • Best For: Post bases, post caps, DTT2Z ties

Highlights:

  • ✓ Listed in ICC-ES ESR-2236
  • ✓ No stripping reported
  • ✗ Only where the table lists SDS
  • ✗ Not for stainless steel connectors

Why SDS Screws Hold Up According to Buyer Reviews

"Exactly what I needed"

"Exactly what I needed to secure the post."

Buyer, October 22, 2025

The one critical review, from Mike on June 25, 2025, was about a half-empty box, not the screw.

Also used: the connector's listed nails, through-bolts, and FastenMaster ThruLok.

The Best Screws for Rim Joists and Joist to Beam are Simpson SD and SDWS Screws

The best screws for rim joists and joist to beam are Simpson SD screws in a hurricane tie on top of the beam, and SDWS Timber through the rim at the corners. End-grain screws hold about 75% of their side-grain withdrawal, per the USDA Wood Handbook, so rim joist screws help connect and stabilize the framing. Where rim joist connections transfer structural loads, use fasteners approved for those loads rather than relying on ordinary screws driven into end grain.

The AWC guide allows toe-nails, a tie rated for at least 100 lb of uplift and lateral load, or a hanger. We use the tie, the cleanest to inspect; one city bans toe-nails alone on freestanding decks.

When To Use These Deck Rim Joist Screws:

  • If the tie is ZMAX, drive galvanized SD9112. If it's stainless steel, SD9112SS.
  • If you're fastening rim corners, use structural screws for the rim joist and pre-drill the ends so you don't split the rim.

Also used: FastenMaster HeadLok, or three 10d nails per joist end in one coastal town's guide.

The Best Deck Framing Screws for Coastal Decks are Simpson Type 316 Stainless Steel Screws

The best deck framing screws for coastal decks are Simpson's Type 316 lines in Type 316 connectors: SD SS in hangers, SDWS Timber SS or SDWH Timber-Hex SS on ledgers, beams and rims, and SDS SS in post hardware. Simpson's stainless steel connector guidance says 304 and 305 fasteners aren't recommended with its 316 connectors.

  • Within 300 ft of salt water, the AWC guide calls for 304 or 316 stainless steel connectors.
  • Simpson says stainless steel connectors may be needed up to 10 miles from the ocean.
  • ER-192 (2018) keeps double-barrier SDWS and SDWH to dry or freshwater exposure.

More in our guide to screws by the coast and 304 vs 316 stainless steel.

Simpson Strong-Drive SDWH Timber-Hex SS Screws

Ideal for:

  • Coastal ledgers, rim corners, docks and piers.

Why It's On The List (Key Features):

  • Simpson's IRC ledger table puts 4" SDWH27 SS every 9" on 12 ft joists: $3.97 a ledger foot (at the time of writing).

When To Use the SDWH Timber-Hex SS:

  • If the deck is near salt and you'd rather drive a hex head than 6-lobe.

BEST COASTAL LEDGER AND RIM SCREWS

Simpson Strong-Drive SDWH Timber-Hex SS Screw

From $50.00 (5" x 10 box; $1.61 a screw for a 4" SDWH19 in the 100 box, at the time of writing)

The Simpson SDWH Timber-Hex screw in Type 316, a tagged bestseller on our store.

Shop Product →

Specifications:

  • Material: Type 316 stainless steel
  • Drive: Hex head, bit included; 0.185" and 0.275"
  • Best For: Coastal ledgers, rims, docks

Highlights:

  • ✓ Simpson IRC ledger table
  • ✓ From $1.61 a screw
  • ✗ 10" and 12" run $9.40 to $15.20
  • ✗ The lag table doesn't apply

Also used: SPAX PowerLag HCR-X and stainless steel lag bolts.

The Best Screws for Blocking and Non-Structural Framing are Eagle Claw #10 x 3" Stainless Steel Deck Screws

The best screws for mid-span blocking, skirting and fascia nailers are #10 x 3" 304 stainless steel deck screws, or 316 near salt. For general-purpose blocking, skirting and fascia nailers, #10 stainless steel deck screws can be a practical choice. Where blocking is required for structural support or bracing, follow the applicable fastening requirements. They never go in a hanger, ledger, tie or any listed connection.

#10 x 3" 304 and 316 Stainless Steel Deck Screws

Ideal for:

  • Mid-span blocking, skirting and fascia nailers.

Why It's On The List (Key Features):

  • Solid 304, so there's no coating for ACQ or copper azole lumber to eat. 3" leaves 1-1/2" in the block.

When To Use These Screws:

  • If the deck is inland, use 304. Within about 3 miles of salt water, use 316 marine grade.
  • If you're within 1" of a block's edge, pre-drill 7/64" for a #10 in softwood.

BEST SCREWS FOR NON-STRUCTURAL FRAMING

Eagle Claw #10 x 3" 304 Grade Stainless Steel Deck Screws

4.8 ★★★★★ (110 reviews)

From $36.00 (100 box, at the time of writing)

What we drive into blocking and nailers inland, and the boards on top. Near salt, the 316 starts at $45.00.

Shop Collection →

Specifications:

  • Material: 304 stainless steel, no coating
  • Size: #10 x 3", Type 17 point
  • Best For: Blocking, nailers, deck boards

Highlights:

  • ✓ Nothing to rust off
  • ✓ A 316 version for salt
  • ✗ Not structural, no code report
  • ✗ Never in hangers, ledgers or ties

Why Eagle Claw #10 x 3" Stainless Steel Deck Screws Hold Up According to Buyer Reviews

"Never broke 1"

"Used 600+ to build a 20x10 deck treated yellow pine. No issues, never broke 1"

Brad O., June 22, 2022

"#10 instead of #9"

After the coated screws on his 12-year-old deck rusted and "just sheered," this buyer switched: "These are #10 instead of #9 which is better for me."

Doug C., May 7, 2023

What Size Screws Should I Use for Deck Framing?

Deck framing screws take the size the connector or maker's table calls for, so screw length for deck framing starts there. That's #9 x 1-1/2" in hanger faces, #9 x 2-1/2" in angled joist holes, and on a ledger, long enough to pass the ledger, sheathing and house band.

For 2x4 wall framing and other lumber, see our guide to choosing wood screws for each job.

Connection Screw Diameter Length Into which member How many Pre-drill
Hanger face SD9112 or SD9112SS #9 1-1/2" Ledger or beam 6 per LUS28, 8 per LUS210 n/a
Angled hanger holes SD9212 or SD9212SS #9 2-1/2" Through joist into header 4 per LUS210, 6 per LUS210-2 n/a
Ledger, code baseline 1/2" HDG lag, washer 1/2" Tip past the band's inside face House band Every 15" on 12 ft joists 1/2" ledger, 5/16" band
Ledger, structural screw SDWS Timber or SDWH 0.220" to 0.275" Ledger board screw length per Simpson's table House band Simpson's table Ledger ends only
Beam plies SDWS Timber 0.220" or 0.275" Simpson's schedule Every ply Simpson's schedule No
Post base or cap SDS 1/4" Connector's table Post or beam Connector's table No
Joist to beam SD9112 in a tie #9 1-1/2" Joist and beam Tie's table n/a
Rim corners SDWS or SDWH SS 0.220" to 0.275" 4-1/2" to 6" Joist end Per plans Near ends
Blocking #10 stainless steel deck screw #10 3" Block n/a 7/64" near ends

Are Deck Screws Good for Framing?

No, deck screws aren't good for framing any listed connection: hangers, ledgers, ties, post bases or beams. Are deck screws OK to use for framing anywhere? Yes, in blocking, nailers and on the boards.

Deck screws vs framing screws comes down to one job each: deck screws hold boards down, and deck framing screws hold the deck up. Boards are in our guide to the best screws for decking. Using deck screws for framing goes wrong in the same few places:

  • Deck or drywall screws in hangers. A Fargo handout: "Deck screws cannot be substituted for other fasteners."
  • Unlisted screws for lags on a ledger. Structural screws for deck framing need a report.
  • Galvanized and stainless steel mixed. Simpson and the AWC guide say one metal per connection.
  • Short nails in angled hanger holes. They miss the header.
  • End-grain screws carrying load. They hold joists in line, nothing more.
  • Other common fails: empty hanger holes, one-row ledgers, ledgers on brick veneer, G90 hangers, and no lateral ties.

What Screws Should I Use for Framing a Deck?

The screws you should use for framing a deck are Simpson Strong-Drive screws matched to each connection. SD Connector screws go in hangers and ties. SDWS Timber or SDWH Timber-Hex go on ledgers, beams and rim corners. SDS goes in post bases and caps that list it.

Stainless steel deck screws go in blocking and on the boards, and that's the whole list of decking frame screws.

Tips on Choosing Deck Framing Screws

What screws to use for deck framing comes down to four checks.

1. Find the code report number on the box

Deck framing screws carry a number: ESR-3046 on SD, ESR-2236 on SDS, ER-192 on double-barrier SDWS. No number, no hanger. Full code picture: what fasteners are required for deck construction.

2. Match the screw finish to the connector finish

The AWC guide: "Fasteners and connectors shall be of the same corrosion-resistant material." In treated lumber, deck framing screws need hot-dip galvanizing or a listed equivalent, stainless steel, silicon bronze or copper (IRC R317.3, R304.3 in 2024), per our pressure treated screw guide.

3. Buy by the connection count, not the box

Twenty hangers with 8 face holes need 160 SD9112SS: two 100 boxes at $124, not a 500 box at $207 (at the time of writing).

4. Plan for inspector access to the rim

Get the frame inspected before the boards go down.

Deck Framing Screw Brands We Carry

At Eagle Claw Fasteners, we carry Simpson Strong-Tie deck framing screws for the frame and our own screws for the boards and non-structural framing. In Simpson: SD Connector SS, plus SDS Heavy-Duty, SDWS Timber and SDWH Timber-Hex in coated and Type 316 versions.

We don't stock the galvanized SD, SDW or SDWS Framing, but can source the rest of Simpson's catalog. No FastenMaster, GRK or SPAX.

FAQs

Is it better to use nails or screws for deck framing? ▶
It's better to use whatever the connection is listed for: hot-dip galvanized nails and listed screws both pass, and deck screws don't. Nails are the code baseline and fast with a palm nailer. Listed SD, SDS and SDWS screws drive where a hammer won't swing. Never mix the two in one hanger.
Are deck screws just as strong as construction screws? ▶
No, deck screws aren't as strong as construction screws for framing. A deck screw holds a board down, and a listed structural screw is tested to carry frame loads, with a report behind it. Builders describe cheap deck screws as brittle in shear. We break it down in construction screw vs deck screw.
What are the codes for attaching deck ledger boards? ▶
The codes for attaching deck ledger boards are IRC R507.9.1.3 and Table R507.9.1.3(1) in the 2018 and 2021 IRC, and R507.2.1 in the 2015 code. They allow staggered 1/2" lags or through-bolts with washers, and listed screws pass on their reports. Lateral ties fall under R507.9.2. See the fasteners the code requires for decks.
Best Screws for Framing: 2x4, 2x2 and 2x6

Leave a Comment

We’d love to hear your thoughts.